Formability Analysis of Crca-IS2 Sheet to Eliminates the Defects during Deep Draw
Keywords:
Finite Element Analysis (FEA), Sheet Metal Bending, Drawing, Simulation, Wrinkling.Abstract
Metal forming operations in industries are performed by the sheet metal processes. In sheet metal work deep
drawing plays a major role to form the desired shapes. Improper design process leads to defected parts which are
not acceptable due to ergonomics as well as aesthetics. Enormous defects during drawing have been discussed in
the literature. FEA of sheet metal drawing was performed by using a blank. During the drawing operation
wrinkling and tearing were observed experimentally. FEA as an effective tool has been concluded for this
technique. The results will help in optimizing the process by changing the input parameters and help the industry
to perform hit and trial on simulator rather than virtual environment
Downloads
References
Alin, P., Ioan, M., Ioan, R., & Florin, B. (2013). Parameters influence on wrinkling in deep drawing cylindrical
cups. Revista de Tehnologii Neconventionale, 17(3), 59-63.
Altinbalik, T., & Tonka, A. (2012). Numerical and experimental study of sheet thickness variation in deep drawing
processes. International Journal of Modern Manufacturing Technologies, 4(2), 9-16.
Kang, B. S., Song, W. J., & Ku, T. W. (2010). Study on process parameters and its analytic application for
nonaxisymmetric rectangular cup of multistage deep drawing process using low carbon thin steel sheet. The
International Journal of Advanced Manufacturing Technology, 49(9), 925-940.
Madake, M. A. D., Naik, D. V. R., & Kulkarni, M. S. S. (2013). Development of a sheet-metal component with a
forming die using CAE software tools (Hyper form) for design validation and improvement. International Journal
of Modern Engineering Research, 3(3), 1787-1791.
Mayavan, T., & Karthikeyan, L. (2013). Experimental and finite element studies on formability of low carbon
steel sheets using deep drawing. International Journal of Engineering and Technology, 5(1), 165-174.
Özek, C., & Bal, M. (2009). The effect of die/blank holder and punch radiuses on limit drawing ratio in angular
deep-drawing dies. The International Journal of Advanced Manufacturing Technology, 40(11), 1077-1083.
Ramezani, M., & Ripin, Z. M. (2012). Analysis of deep drawing of sheet metal using the marform process. The
International Journal of Advanced Manufacturing Technology, 59(5), 491-505.
Reddy, R. V., Reddy, D. T. J., & Reddy, D. G. (2012). Effect of various parameters on the wrinkling in deep
drawing cylindrical cups. International Journal of Engineering Trends and Technology, 3(1), 53-58.
Reddy, R. V., Reddy, T. A., & Reddy, G. C. M. (2012). Optimization of blank holder force to control wrinkling
and fracture of cylindrical cups in deep drawing. International Journal of Engineering Trends and Technology,
(5), 669-676.
Sen, N., & Kurgan, N. (2016). Improving deep drawability of HC300LA sheet metal by warm forming.
International Journal of Advanced Manufacturing Technology, 82(5), 985-995.
Singh, C. P., & Agnihotri, G. (2015). Study of deep drawing process parameters: a review. International Journal
of Scientific and Research Publications, 5(2), 1-15.
Vosniakos, G. C., & Giannakakis, T. (2013). A knowledge-based manufacturing advisor for press worked sheet
metal parts. Journal of Intelligent Manufacturing, 24(6), 1253-1266.
Wang, J., Goel, A., & Yang, F. (2009). Blank optimization for sheet metal forming using multi-step finite element
simulations. The International Journal of Advanced Manufacturing Technology, 40(7), 709-720.
Wei, D., Cui, Z., & Chen, J. (2008). Optimization and tolerance prediction of sheet metal forming process using
response surface model. Computational Materials Science, 42(2), 228-233.
Wifi, A., & Mosallam, A. (2007). Some aspects of blank-holder force schemes in deep drawing process. Journal
of Achievements in Materials and Manufacturing Engineering, 24(1), 315-323.
Yang, L., Mori, K., & Tsuji, H. (2008). Deformation behaviors of magnesium alloy AZ31 sheet in cold deep
drawing. Transactions of Nonferrous Metals Society of China, 18(1), 86-91
